ST-Link V2 Programmer For STM8 and STM32 is fully consistent with the official version, support for automatic upgrades, support the full range STM32 SWD (only 4pins including SWCLK, SWDIO, and power) and a full range STM8 SWIM (only 4pins including SWIM, Reset and power) download and debug.
Use this device to send program code to the 32-bit STM32 ARM Cortex or 8-bit STM8 microcontrollers. The header for this ST-Link v2 programmer contains connections for 5V, 3.3V, SWCLK, SWDIO, SWIM, Reset (RST/NRST) and GND. The connector on the opposite side of this device is a USB connector and is intended to be plugged into the computer.
You can download the Drivers by clicking here
Note: The product is available in Multiple colors and design Will be shipped randomly.
Supports For ST-LINK V2 :
- ST-LINK Utility 2.0 and above.
- STVD 4.2.1 and above.
- STVP 3.2.3 and above.
- IAR EWARM V6.20 and above.
- IAR EWSTM8 V1.30 and above.
- KEIL RVMDK V4.21 and above.
Features :
- PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable!
- Interface definition directly marked on the shell, clear, convenient and practical!
- 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V
- Shell characters using laser engraving, never fade off! Permanent clarity!
- 500MA internal resettable fuse, complete protection of your expensive computer motherboard!
- Red and blue color LED indicator, allowing you to always observe ST-LINK V2 working condition!
- With 4 DuPont line, so you can easily respond to different target board line order!
- Use anti-static bag packaging.
-
SWIM specific features:
- SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector
- 1.65 V to 5.5 V application voltage supported on SWIM interface
- SWIM low-speed and high-speed modes supported
- SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed
- SWIM cable for connection to the application
- Direct firmware update feature supported (DFU)
- Status LED which blinks during communication with the PC
- Operating temperature 0 to 50°C
Package Includes:
1 x ST-Link V2 Programmer For STM8 and STM32.
1 x Connecting Wires.
shivamverma3828 (verified owner) –
Nice quality working excellent with my bluepill and discovery boards⭐⭐⭐⭐
shivamverma3828 –
arunsmailid4u (verified owner) –
It works but! There are 2 set of power pins but only one of them work!
If you have trouble connecting your STM32 board, switch the power pins sides and try.
arunsmailid4u –
SILICON HI-TECH ENGINEERING (verified owner) –
Overall good
SILICON HI-TECH ENGINEERING –
SILICON HI-TECH ENGINEERING (verified owner) –
Overoll good
SILICON HI-TECH ENGINEERING –
anupam dubey (verified owner) –
excellent performance with st visual programmer.
anupam dubey –
harikrishnan527 (verified owner) –
works
harikrishnan527 –
Rishabh Kalkundri (verified owner) –
Best quality. Fast delivery. Worked great with my nRF51822 project.
Rishabh Kalkundri –
Manan Chevli (verified owner) –
Fast delivery and working well as expected. It also comes with printout of pinouts.
Manan Chevli –
Subhojit Roy –
As described
Prompt delivery
Subhojit Roy –
Shridhar Patil (verified owner) –
Product is good. Immediate delivery. Thanks.
Shridhar Patil –
choralsilence (verified owner) –
it works like a charm (the pin diagram given on the accompanying sheet is wrong, the one on the case is what worked for me)
choralsilence –
Atin Agarwal –
Nice product
Atin Agarwal –