Development Board
Showing all 43 results
-
Best Prices, Boards Compatible with Arduino
Uno R3 CH340G ATmega328p Development Board Compatible with Arduino
-17%
Best Prices, Boards Compatible with ArduinoUno R3 CH340G ATmega328p Development Board Compatible with Arduino
SKU: 44497- Microcontroller ATmega328 (SMD) – Interface CH340G
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 5-20V
- Digital I / O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins: 6
SKU: 44497Other ESP WIFI ModulesESP8266 NodeMCU CP2102 Board
SKU: 18821- Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled
- Arduino-like hardware IO
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, DCXO and power management units
- Onboard USB to serial chip to easily program and upload codes from the Arduino IDE
- Embeds logic level converter circuits
- Has onboard 3.3V regulator to ensure enough power to function as your go-to WiFi chip!
- Easy access to the GPIO pins for easy prototyping
- ESP-12E Processor
- Easy to use breadboard friendly form factor
SKU: 18821Best Prices, Other ESP WIFI ModulesNodeMcu ESP8266 V3 Lua CH340 Wifi Dev. Board
SKU: 62160- Power input: 4.5V ~ 9V (10VMAX), USB-powered
- Transfer rate: 110-460800bps
- Support UART / GPIO data communication interface
- Support Smart Link Smart Networking
- Working temperature: -40°C ~ + 125°C
- Drive Type: Dual high-power H-bridge
- Don’t need to download resetting
- A great set of tools to develop ESP8266
- Flash size: 4MByte
- Lowest cost WI-FI
SKU: 62160AVR Microcontroller Board, Best PricesATTINY85 USB Development Board
SKU: 31126- Support for the Arduino IDE 1.0 + (OSX/Windows/Linux).
- Power via USB or External Source or 7-16 v to 5 v (automatic selection).
- The Onboard, 150 ma 5 v Regulator.
- Built-in USB and serial were debugging).
- 6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB).
- 8 k Flash Memory (about 6 k after bootloader).
- The I2C and SPI (vis USI).
- The Power LED and the Test/Status LEDs.
SKU: 31126Boards Compatible with ArduinoPro Micro 5V 16M Mini Leonardo Microcontroller Development Board For Arduino
Boards Compatible with ArduinoPro Micro 5V 16M Mini Leonardo Microcontroller Development Board For Arduino
SKU: 110787- ATMEGA32U4 running in 5V / 16MHz
- Support Arduino IDE V1.0.1
- Micro USB interface programming on the board
- Four 10-bit ADC pin
- 12 digital I / O (5 PWM capability)
- Rx and Tx hardware serial connection
SKU: 110787Boards Compatible with ArduinoUNO R3 CH340G ATMega328P compatible with arduino + Cable
SKU: 48065- A basic Arduino Kit including everything to get started.
- It includes a quality proven Arduino Cable.
- Microcontroller ATmega328 (SMD) – Interface CH340G
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Digital I / O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins: 6
SKU: 48065Best Prices, Boards Compatible with ArduinoUno R3 Board without Cable compatible with Arduino
SKU: 14140- Supported by Arduino IDE
- Operating Voltage: 5 V
- Input Voltage: 7 to 12 V
- Digital I/O pins: 14
- PWM Pins: 6
- Analog Input pins: 6
- Flash Memory: 32 KB (0.5 KB used by bootloader)
- SRAM: 2 KB
- EEPROM: 1 KB
SKU: 14140Best Prices, Kits compatible with ArduinoArduino Uno R3 Beginners Kit
SKU: 31475- Great for Starting with Arduino Programming
- A variety of components are included in this pack to try out different projects.
- The kit comes with quality components assured by Robu.in.
- All-in-one kit, a great starter kit for learning to code.
- Microcontroller ATmega328 (SMD) – Interface CH340G
SKU: 31475ARM MicrocontrollerCore Board STM8S103F3P6 STM8 Development Board Minimum System Board
SKU: 31263- Chipboard STM32F103C8T6
- On board, SWIM interface and reset button
- Micro USB line or the 2.54 pin to link to the power with the input voltage 4.5V-15V.
- Power light and the Demo indicator light
- Leads all the pins and has detailed label for the Pins.
- Support SWIM debug mode.
SKU: 31263Best Prices, PIC ProgrammerOut of stock
PICkit3 Debugger Programmer Emulator Controller Development Board
-10%
Best Prices, PIC ProgrammerPICkit3 Debugger Programmer Emulator Controller Development Board
SKU: 28352- Full-speed USB support using Windows standard drivers
- Real-time execution
- Processors run at maximum speeds
- Built-in over-voltage/short circuit monitor
- Low voltage to 5V (1.8 to the 5V range)
- Read/write program and data memory of the microcontroller
- Program up to 512K byte flash.
SKU: 28352PIC ProgrammerPICkit3 Debugger Programmer Emulator Controller Development Board
SKU: 1814218- Full-speed USB support using Windows standard drivers
- Real-time execution
- Processors run at maximum speeds
- Built-in over-voltage/short circuit monitor
- Low voltage to 5V (1.8 to the 5V range)
- Read/write program and data memory of the microcontroller
- Program up to 512K byte flash.
SKU: 1814218Boards Compatible with ArduinoUno R3 compatible with Arduino + Cable + Transparent acrylic case for Uno R3
Boards Compatible with ArduinoUno R3 compatible with Arduino + Cable + Transparent acrylic case for Uno R3
SKU: 48057- A basic Arduino Kit including everything to get started.
- It includes a quality proven Arduino Cable.
- It includes a strong and sturdy Transparent Acrylic Case.
- Micro-controller : ATmega328
- Operating Voltage: 5V
- Input Voltage (recommended) : 7-12V
- Digital I/O Pins: 14 (of which 6 provide PWM output)
- Analog Input Pins: 6
SKU: 48057AVR Microcontroller BoardDigispark ATTINY85 Mini USB Development Board
SKU: 31117- High Performance, Low Power AVR® 8-Bit Microcontroller
- Non-volatile Program and Data Memories
- 512 Bytes In-System Programmable EEPROM
- 512 Bytes Internal SRAM
- USI – Universal Serial Interface (12C, SPI, 1-wire) with Start Condition Detector
- 10-bit ADC
- 4 Single Ended Channels
- Two Differential ADC Channel Pairs with Programmable Gain (1x, 20x)
- Low Power Consumption
- Active Mode:1 MHz, 1.8V: 300 µA
SKU: 31117Other ESP WIFI ModulesNodeMCU ESP8266 Serial Port Baseboard Lua WIFI Development Board
SKU: 31313- The perfect solution for breaking out the pins from Lua V3 Nodemcu.
- Lead-out all the IO ports of the ESP-12E development board
- Lead out the pins of 5V and 3.3V power supply
- Convenient to connect with peripheral modules
- Onboard 5V / 1A DC-DC step-down converter circuit
- Onboard power indicator
- With DC power jack 6-24V.
SKU: 31313Best Prices, Kits compatible with ArduinoAdvanced Kit for Arduino
SKU: 31816- All-in-one kit, a great starter kit for learning to code.
- Model Type: UNO Rev R3
- Microcontroller Chip: ATmega328
- Input Voltage(Recommended): 7-12V
- Operating Voltage: 5
- Analog I/O Pins: 6
- Digital I/O Pins: 14 (of which 6 provide PWM output)
SKU: 31816Kits compatible with ArduinoUno Learning kit for Arduino
SKU: 31821- All-in-one kit, a great starter kit for learning coding.
- Microcontroller ATmega328 (SMD) – Interface CH340G
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 5-20V
- Digital I / O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins: 6
SKU: 31821Other ESP WIFI ModulesESP8266 Serial Port To Wi-Fi Module, FL-M1S
SKU: 61977- 802.11 b/g/n
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, DCXO and power management units
- +19.5dBm output power in 802.11b mode
- Power down leakage current of <10uA
- Integrated low power 32-bit CPU could be used as application processor
SKU: 61977Beagle BoardBeagleBone Black REV C
SKU: 55793- Sitara AM3358BZCZ100 ARM Cortex-A8 32-Bit RISC microprocessor, up to 1GHz
- Onboard HDMI to connect directly to TVs and monitors
- More and faster memory now with 512MB DDR3L 400MHz SDRAM, 4GB eMMC Memory
- Onboard storage frees up the microSD card slot for greater expansion
- Support for existing Cape plug-in boards
- TPS65217C PMIC regulator and one additional LDO
- Debug support: Optional onboard 20-pin CTI JTAG
- HS USB 2.0 Client and Host ports
SKU: 55793PIC ProgrammerPIC K150 USB Automatic Develop Microcontroller Programmer with ICSP Cable (Body width: 4 mm)
PIC ProgrammerPIC K150 USB Automatic Develop Microcontroller Programmer with ICSP Cable (Body width: 4 mm)
SKU: 43286- Support the most popular programming PIC chips, read, encryption and other features!
- No external power supply, communication, and power is only a USB cable to print complete, without any cable.
- PICSTARTPLUS much faster rate than programming.
- Can easily read the contents of the chip program area.
- Automatic programming verification.
- Comprehensive information prompts, allowing users to understand the working state.
SKU: 43286PIC ProgrammerOut of stock
PIC K150 USB Automatic Develop Microcontroller Programmer with ICSP Cable (Body width: 4 mm)
PIC ProgrammerPIC K150 USB Automatic Develop Microcontroller Programmer with ICSP Cable (Body width: 4 mm)
SKU: 1378250- Support the most popular programming PIC chips, read, encryption and other features!
- No external power supply, communication, and power is only a USB cable to print complete, without any cable.
- PICSTARTPLUS much faster rate than programming.
- Can easily read the contents of the chip program area.
- Automatic programming verification.
- Comprehensive information prompts, allowing users to understand the working state.
SKU: 1378250Boards Compatible with ArduinoLilyPad 328 ATmega328P Main Board 16M Compatible with Arduino
SKU: 28446- Microcontroller: ATmega168 or ATmega328V
- Operating Voltage: 2.7-5.5 V
- Digital I/O Pins: 14
- PWM Channels: 6
- Analog Input Channels: 6
- DC Current per I/O Pin: 40 mA
- Board will run from 2V to 5V.
- The latest version of the LilyPad supports automatic reset for even easier programming.
- The back side of the LilyPad is now completely flat!
SKU: 28446Cytron Motor DriversCytron Maker UNO Microcontroller Board- Arduino UNO Compatible Module
SKU: 56432- SMD ATmega328P microcontroller(the same microcontroller on Arduino UNO) with Optiboot (UNO) Bootloader
- USB Programming facilitated by the CH340
- Input voltage: USB 5V, from computer, power bank or standard USB adapter
- Piezo buzzer that will act as simple audio output
- 500mA (maximum) 3.3V voltage regulator
- 0-5V outputs with 3.3V compatible inputs
- 14 Digital I/O Pins (6 PWM outputs)
- 6 Analog Inputs
- ISP 6-pin Header
SKU: 56432PIC ProgrammerATMEGA16 ATmega 32 ISP AVR Minimum Development System Board Module
SKU: 43675- 32 I/O pin all the leads.
- Classic ATmega16 minimum system, eliminating the hassle of soldering.
- Support chips: ATmega16/ATmega32 and chip which pin-compatible.
- Power supply: power adapter or external expansion pin power supply (not support ISP download interface power supply)
- DC-005 Power Block (supporting the transposon is 5.5*2.1mm).
- Reset: Power-on-reset and reset button.
- Power LED (D1) and the program run indicator (D2).
- Standard ISP download interface.
SKU: 43675Breakout BoardSparkFun Cryptographic Co-Processor Breakout – ATECC608A
SKU: 1037779- Operating Voltage: 2.0V-5.5V
- Active Current Draw (for ATECC608A): 16 mA
- Sleep Current : <150 nA
- Guaranteed Unique 72-bit Serial Number
- Offers two Qwiic ports for plug and play functionality
- Creates & securely stores unique asymmetric key pairs
- Provides internal high quality FIPS random number generator
SKU: 1037779Boards Compatible with ArduinoAdafruit Feather M4 Express – Featuring ATSAMD51 – ATSAMD51 Cortex M4
SKU: 1104417- ATSAMD51 32-bit Cortex M4 core
- 512 KB flash, 192 KB RAM
- 3.3V regulator with 500mA peak current regulator
- USB bootloader and serial port debugging
- Built-in 100mA lipoly charger with charging status indicator LED
SKU: 1104417IoT CamerasLILYGO T-Journal ESP32 OLED Normal Camera Module Development Board With OV2640 SMA Wifi 3dbi Antenna
IoT CamerasLILYGO T-Journal ESP32 OLED Normal Camera Module Development Board With OV2640 SMA Wifi 3dbi Antenna
SKU: 1031133- Material: Metal
- FLASH: QSPI flash/SRAM, up to 4 x 16 MB
- SRAM: 520 kB SRAM
- KEY: reset，IO32
- Display: 0.91 SSD1306
- Power Indicator Lamp: Red
- USB to TTL: CP2104
- Camera: OV2640 2Megapixel
- High sensitivity and low light operation standard SCCB interface.
SKU: 1031133Boards Compatible with ArduinoOut of stock
pcDuino3B – 1GHz Cortex Dual Core 1G RAM, Compatible With Arduino
-7%
Boards Compatible with ArduinopcDuino3B – 1GHz Cortex Dual Core 1G RAM, Compatible With Arduino
SKU: 3331- 100% compatible with original Arduino Shields
- 100% compatible with Linux and Android
- Further support for:
- C, C ++ with GNU tool
- Java with standard Android SDK Python
- Arduino pin header, Arduino UNO Slots: 14x GPIO, 2x PW M, 6x ADC, 1x UART, 1xSPI, 1x I2C
- Ethernet 10M/100Mbps, WiFi, SATA
SKU: 3331ARM MicrocontrollerOut of stock
Olimex OLIMEXINO-STM32 ARDUINO/MAPLE like Board with STM32F103RBT60
ARM MicrocontrollerOlimex OLIMEXINO-STM32 ARDUINO/MAPLE like Board with STM32F103RBT60
SKU: 11181- STM32F103RBT6 microcontroller
- UEXT connector which allows many existing modules like RF, ZIGBEE, GSM, GPS to be connected
- Allows RTC – Real Time Clock.
- CAN with driver allows automotive applications
- micoSD-card for data logging
- NOISE IMMUNE design.
- A mini USB connector is used, which is common.
- 4 mount holes make board attachment easier.
SKU: 11181
Robu.in wants to send you updates. Click Allow to subscribe.
