DC motor driver
Showing all 39 results
-
-
-
Relay Modules
5-36v Switch Drive High-power MOSFET Trigger Module
SKU: 52812This 5-36v Switch Drive High-power MOSFET Trigger Module can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps,  solenoid valves, PWM, motor speed control, lamp brightness. etc.
SKU: 52812 -
Best Prices
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
SKU: 43740- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: 43740 -
Breakout Board
IRF520 MOSFET Driver Module for Arduino ARM Raspberry pi
SKU: 44050- Voltage: 3.3 – 5V.
- Ports: Digital Level.
- Output load voltage: 0-24 V.
- Output load current: <5A (1A above need to add heat sink).
- Platform: Arduino, MCU, ARM, raspberry pi.
- Using original IRF520 Power MOS, you can adjust the output PWM
SKU: 44050 -
Cytron Motor Drivers
Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
SKU: 2777- Bi-directional control for 1 brushed DC motor, single channel
- Support motor voltage ranges from  5V to 30V.
- Maximum current up to 13A continuous and 30A peak (10 seconds).
- 3.3V and 5V logic level input.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: 2777 -
Cytron Motor Drivers
Out of stock
Cytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
Cytron Motor DriversCytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
SKU: 3405- Bi-directional control of 2 brushed DC motor.
- Support motor voltage ranges from 5V to 25V.
- Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: 3405 -
Brushed / Brushless DC motor Driver
20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
Brushed / Brushless DC motor Driver20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
SKU: 51649- Adjustable speed range: 0%-100%.
- Speed adjustment way: Potentiometer.
- Output voltage: Linear under load.
- Speed control type: Basins.
- Output voltage: Load Linear
- Type: Adjusting flow
- The motor running condition adjustment: Forward  / Stop / Reverse
SKU: 51649 -
Stepper Motor Drivers
L298N Dual H Bridge DC/Stepper Motor Driver Controller Module
SKU: 51971- Driver chip: L298N Dual H Bridge
- Supply voltage: VMS 5V – 35V
- Peak current IO: 2A per bridge
- Max power consumption: 20W
- Provides 4 LEDs that reflect the state of the control logic
- Independent direction, speed, and braking for each motor
SKU: 51971 -
Cytron Motor Drivers
MD13S 13Amp DC Motor Driver – GROVE Compatible
SKU: 24027-
Support motor voltage ranges from 6V to 30V
-
Maximum current up to 13A continuous and 30A peak (10 seconds).
-
GROVE compatible
-
3.3V and 5V logic level input.
-
SMD compatible
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 1
- No. of Channels: 1
SKU: 24027 -
-
Stepper Motor Drivers
TB6600 Stepper Motor Driver Controller 8~50V 4.5A
SKU: 49111- Supply Voltage: 8V – 50V DC (36V recommended).
- Output current: 0.3A – 4.5A (peak value of 5A).
- Micro Step: 1, 2, 8, 16.
- Maximum PWM frequency:Â 200kHz.
- Adjustments for the maximum current of the LED: 1A, 2.2A, 3.3A, 4.5A.
- Operating temperature: -10 to + 45 ° С.
SKU: 49111 -
Cytron Motor Drivers
Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2
SKU: 2774- Bi-directional control of 1 brushed DC motor.
- Motor Voltage: 5V – 30V.
- Maximum Current: 80A peak (1 second), 30A continuously.
- Reverse polarity protection.
- 3.3V and 5V logic level input.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: 2774 -
Brushed / Brushless DC motor Driver
Out of stock
Monster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)
Brushed / Brushless DC motor DriverMonster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)
SKU: 28546- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 34 mΩ
- Maximum PWM frequency: 10 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
SKU: 28546 -
Brushed / Brushless DC motor Driver
Out of stock
Dual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A)
Brushed / Brushless DC motor DriverDual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A)
SKU: 28535- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 19 mΩ (per leg)
- Maximum PWM frequency: 20 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
SKU: 28535 -
Cytron Motor Drivers
Cytron Smart Drive Mdds30 Dual 30A (80A Peak)
SKU: 29672- Battery low voltage indicator.
- Battery over voltage indicator.
- Thermal protection.
- Current limit protection.
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Dimension: 103 x 97 x 40 (LxWxH) mm.
SKU: 29672 -
Cytron Motor Drivers
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
SKU: 4565Â
-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
SKU: 4565 -
-
Dimension Engineering Motor Drivers, Motor/Drivers & Accessories on Sale
Sabertooth Dual 12A Motor Driver
-21%
Dimension Engineering Motor Drivers, Motor/Drivers & Accessories on SaleSabertooth Dual 12A Motor Driver
SKU: 4692- 12A continuous, 25A peak per channel Up to 24V in
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Peak Current (A): 25A
- Continuous Current (A): 12
- Operating Voltage(VDC): 18 to 24V
- No. of Channels: 2
SKU: 4692 -
Cytron Motor Drivers
Cytron 25A 7V-58V DC motor driver with Switch and Potentiometer Control (MD25HV POT)
Cytron Motor DriversCytron 25A 7V-58V DC motor driver with Switch and Potentiometer Control (MD25HV POT)
SKU: 497900- Bidirectional control for one brushed DC motor.
- Maximum Motor Current: 25A continuous, 60A peak.
- 5V output for the host controller (250mA max).
- Buttons for quick testing.
- PWM frequency up to 40kHz.
- Dual Input Mode: PWM/DIR or Potentiometer/Switch Input.
SKU: 497900 -
Cytron Motor Drivers
Cytron 10Amp 7V-30V DC Motor Driver for R/C (2 Channel) MDDRC10
SKU: 945382- Operating Voltage: DC 7 V to 30 V
- Maximum Motor Current: 10 A continuous, 30 A peak
- Motor Output PWM Frequency: 20 kHz
- RC Input Voltage (RC1 & RC2): Low Level: 0-0.7 V | High Level: 1.5-15 V
- Output Maximum Current: 0-500 mA
SKU: 945382 -
Dimension Engineering Motor Drivers
Sabertooth Dual 25A Motor Driver
SKU: 4698- 25A continuous, 50A peak per channel
6-30V nominal, 33.6V absolute maximum - Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Input modes: Analog, R/C, simplified serial, packetized serial
SKU: 4698 - 25A continuous, 50A peak per channel
-
Dimension Engineering Motor Drivers
Sabertooth Dual 32A Motor Driver
SKU: 4702- 32A continuous, 64A peak per channel
- 6-30V nominal, 33.6V absolute maximum
- Synchronous regenerative drive
- Ultrasonic 30 kHz switching frequency
- Thermal and overcurrent protection
- Battery protection mode
- USB control and monitoring
- USB serial converter mode for Kangaroo x2
- Configurable current limiting
- Custom user modes
- 12-bit motor outputs
SKU: 4702 -
Cytron Motor Drivers
Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)
SKU: 8014-
Input Voltage (Motor): 10 – 45VDC
- Maximum current up to 100A peak (1 second), 60A continuously, each channel.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Suitable for combat or sumo robot.
- Battery Low Voltage Monitoring Mode
- DC Brush motor Driver, not for brushless motor
- Dual Channels, it can drive two brush motor independently, or mixed.
- Version: Rev 1.10
SKU: 8014 -
-
-
Cytron Motor Drivers
Cytron 2Amp Motor Driver Shield
SKU: 16014-
Logic control, 5V from Arduino main board
-
Polarity protection for External motor power input
-
2 fast test buttons for each motor channel
-
Motor Driven Voltage：6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source)
-
Up to 2A current each channel
-
Pin 4, 5,6,7 are used to drive two DC motor
-
Support PWM speed control
-
Support advance speed control
SKU: 16014 -
-
-
Cytron Motor Drivers
Cytron 10A Dual Channel DC Motor Driver Shield for Arduino Uno
SKU: 497899- Bidirectional control for two brushed DC motor.
- Control one unipolar/bipolar stepper motor.
- Buck regulator to produce 5V output (500mA max).
- Buttons for quick testing.
- LEDs for motor output state.
SKU: 497899 -
Cytron Motor Drivers
Cytron FD04A 4-Channel Motor Driver
SKU: 16010- Industrial grade PCB.
- Vmotor: 7 V to 25 V DC.
- Each component is soldered properly and tested.
- Able to drive 4 DC motor at 2.5A (peak), 1.5A continuously.
- 2 LEDs as a direction indicator for each motor.
- 1 LED as a power indicator.
- A pluggable connector for more user-friendly design.
- Fully compatible with Cytron DIY project, Flexibot – Using Transwheel (PR19).
SKU: 16010 -
Cytron Motor Drivers
Cytron Dual channel 10A Motor Driver UNO Robot Controller
SKU: 49866- Onboard 1A (maximum) 5V voltage regulator.
- Onboard 500mA (maximum) 3.3V voltage regulator.
- 0-5V digital outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
- 6 Analog Inputs (Can be digital I/O too).
- Maximum current up to 10A continuous and 30A Peak.
- ISP 6-pin Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- R3 Shield Compatible.
SKU: 49866 -
Cytron Motor Drivers
Cytron Driver HAT-MDD10
SKU: 29670- Support motor voltage ranges from 6VDC to 24VDC.
- Onboard the test button for manual control of the motor.
- Every channel output built with LED indicator.
- Current limiting at 30A.
- Operating Voltage(VDC): 6 to 24
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 10
- No. of Channels: 2
- Operating Modes: PWM (Lock-Antiphase and Sign-Magnitude): Yes, UART: No, Analog:No, RC Servo Signal: No
SKU: 29670 -
Dimension Engineering Motor Drivers
Sabertooth Dual 5A Motor Driver for R/C
SKU: 4689- Operating Voltage(VDC): 6-18
- Peak Current (A): 10
- Continuous Current (A): 5
- No. of Channels: 2
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode-compatible with: 6-12 cell NiMH or NiCd, 2s-4s LiPo, 6V or 12V lead acid (not 18+V lead acid!)
SKU: 4689 -
Cytron Motor Drivers
Cytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)
SKU: 2784- Bi-directional control for a single brushed DC motor.
- Support input voltage from 8V to 28V.
- Maximum current up to 190A peak (1 minute), 175A (2 minutes) or 160A (continuously).
- 16 KHz switching frequency for quiet operation.
- LiPo battery low voltage warning.
- Thermal protection.
SKU: 2784 -
Brushed / Brushless DC motor Driver
Sabertooth Dual 5A Motor Driver
SKU: 4686- Input Voltage: 6V to 18V
- Compatible with: 6-12 cell NiMH or NiCd, 2s-4s LiPo
- 5A continuous per channel, 10A peak
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
SKU: 4686 -
Brushed / Brushless DC motor Driver
Out of stock
Cytron Smartdrive40 40Amp Dc Motor Driver (Peak 80Amp) Mds40A
Brushed / Brushless DC motor DriverCytron Smartdrive40 40Amp Dc Motor Driver (Peak 80Amp) Mds40A
SKU: 2780- Bi-directional control for a single brushed DC motor.
- Support motor from 7V to 25V.
- Maximum current up to 80A peak (1 second), 40A (5 minutes) or 30A (> 20 minutes) continuously.
- 16 KHz switching frequency for quiet operation.
- Reverse polarity protection.
- LiPo battery low voltage warning.
- Thermal protection.
- Current limiting base on temperature.
SKU: 2780
