Cytron
Showing all 37 results
-
Cytron Motor Drivers
Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
SKU: 2777- Bi-directional control for 1 brushed DC motor, single channel
- Support motor voltage ranges from 5V to 30V.
- Maximum current up to 13A continuous and 30A peak (10 seconds).
- 3.3V and 5V logic level input.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: 2777 -
Cytron Motor Drivers
Out of stock
Cytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
Cytron Motor DriversCytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
SKU: 3405- Bi-directional control of 2 brushed DC motor.
- Support motor voltage ranges from 5V to 25V.
- Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: 3405 -
Cytron Motor Drivers
MD13S 13Amp DC Motor Driver – GROVE Compatible
SKU: 24027-
Support motor voltage ranges from 6V to 30V
-
Maximum current up to 13A continuous and 30A peak (10 seconds).
-
GROVE compatible
-
3.3V and 5V logic level input.
-
SMD compatible
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 1
- No. of Channels: 1
SKU: 24027 -
-
Cytron Motor Drivers
Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2
SKU: 2774- Bi-directional control of 1 brushed DC motor.
- Motor Voltage: 5V – 30V.
- Maximum Current: 80A peak (1 second), 30A continuously.
- Reverse polarity protection.
- 3.3V and 5V logic level input.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: 2774 -
Cytron Motor Drivers
Advanced Auto-Calibrating Line Sensor LSA08
SKU: 6182- 8 sensor pairs spaced 16mm.
- 12V input power
- Onboard Mode and a Select button for instant configuration of LSA08
- LCD display unit showing 8 sensors analog value with bar chart and line position.
- Simple Auto-Calibration function to the line following surface.
- Low current consumption (typically 26mA)
- Works on glossy or reflective surface
- Refresh rate up to 200Hz.
SKU: 6182 -
Cytron Motor Drivers
Cytron Smart Drive Mdds30 Dual 30A (80A Peak)
SKU: 29672- Battery low voltage indicator.
- Battery over voltage indicator.
- Thermal protection.
- Current limit protection.
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Dimension: 103 x 97 x 40 (LxWxH) mm.
SKU: 29672 -
Cytron Motor Drivers
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
SKU: 4565-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
SKU: 4565 -
-
-
Cytron Motor Drivers
Enhanced Cytron 40Amp DC Motor Driver (Peak 80amp) MDS40B
SKU: 11648-
Bi-directional control for a single brushed DC motor.
-
Support motor from 10V to 45V.
-
Maximum current up to 80A peak, reduce to 40A gradually according to temperature.
-
16 KHz switching frequency for quiet operation.
-
NO Reverse polarity protection.
-
Protection of overvoltage.
SKU: 11648 -
-
-
Cytron Motor Drivers
10A Motor Driver Shield – MD10
SKU: 3408- Bi-directional control of 1 brushed DC motor.
- Support motor voltage ranges from 7V to 25V, .
- Maximum current up to 10A continuous and 15A peak (10 seconds).
- Solid state components provide faster response time and eliminate the wear and tear of a mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
- Speed control PWM frequency up to 10KHz.
- Selectable digital pins for PWM and DIR.
SKU: 3408 -
Cytron Motor Drivers
Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)
SKU: 8014-
Input Voltage (Motor): 10 – 45VDC
- Maximum current up to 100A peak (1 second), 60A continuously, each channel.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Suitable for combat or sumo robot.
- Battery Low Voltage Monitoring Mode
- DC Brush motor Driver, not for brushless motor
- Dual Channels, it can drive two brush motor independently, or mixed.
- Version: Rev 1.10
SKU: 8014 -
-
Cytron Motor Drivers
Cytron 2Amp Motor Driver Shield
SKU: 16014-
Logic control, 5V from Arduino main board
-
Polarity protection for External motor power input
-
2 fast test buttons for each motor channel
-
Motor Driven Voltage：6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source)
-
Up to 2A current each channel
-
Pin 4, 5,6,7 are used to drive two DC motor
-
Support PWM speed control
-
Support advance speed control
SKU: 16014 -
-
Cytron Motor Drivers
Cytron Arduino PS2 Shield
SKU: 2506- 5V powered low current consumption.
- Simple to use UART protocol
- Vibrator motor on PS2 is controllable.
- Wired and Wireless PS2 controller is supported.
- PS2 Controller will automatically operate in analog mode.
- A status LED
- Jumper selector to select different UART Baud Rate (9600, 57600, 115200).
- Jumper selectors to select different digital pin as UART TX and RX pin.
SKU: 2506 -
Cytron Motor Drivers
Cytron ESP8266 WiFi Shield V2.0 W/ Micro SD Card Slot For Arduino Uno
SKU: 43298- Basically, Rev2.0 utilize WROOM-02 instead of ESP8266-12 as the WiFi module.
- Separate 3.3V voltage regulator for ESP8266-12 WROOM-02 module, 500mA max output.
- Each and every board is preassembled and tested before it is being shipped out to you.
- 802.11 b/g/n.
- Support Wi-Fi Direct (P2P), soft-AP.
- Integrated TCP/IP protocol stack.
SKU: 43298 -
Cytron Motor Drivers
Cytron FD04A 4-Channel Motor Driver
SKU: 16010- Industrial grade PCB.
- Vmotor: 7 V to 25 V DC.
- Each component is soldered properly and tested.
- Able to drive 4 DC motor at 2.5A (peak), 1.5A continuously.
- 2 LEDs as a direction indicator for each motor.
- 1 LED as a power indicator.
- A pluggable connector for more user-friendly design.
- Fully compatible with Cytron DIY project, Flexibot – Using Transwheel (PR19).
SKU: 16010 -
PIC Development board
Cytron 40 pins PIC Start Up Kit SK40C
SKU: 10095- PIC Start Up Kit SK40C
-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
Operating Voltage Range: 7V – 15VDC
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
-
UART connection to interface with other controller or even computer.
SKU: 10095 -
Cytron Motor Drivers
Cytron Dual channel 10A Motor Driver UNO Robot Controller
SKU: 49866- Onboard 1A (maximum) 5V voltage regulator.
- Onboard 500mA (maximum) 3.3V voltage regulator.
- 0-5V digital outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
- 6 Analog Inputs (Can be digital I/O too).
- Maximum current up to 10A continuous and 30A Peak.
- ISP 6-pin Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- R3 Shield Compatible.
SKU: 49866 -
Cytron Motor Drivers
Cytron Driver HAT-MDD10
SKU: 29670- Support motor voltage ranges from 6VDC to 24VDC.
- Onboard the test button for manual control of the motor.
- Every channel output built with LED indicator.
- Current limiting at 30A.
- Operating Voltage(VDC): 6 to 24
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 10
- No. of Channels: 2
- Operating Modes: PWM (Lock-Antiphase and Sign-Magnitude): Yes, UART: No, Analog:No, RC Servo Signal: No
SKU: 29670 -
-
Cytron Motor Drivers
Cytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)
SKU: 2784- Bi-directional control for a single brushed DC motor.
- Support input voltage from 8V to 28V.
- Maximum current up to 190A peak (1 minute), 175A (2 minutes) or 160A (continuously).
- 16 KHz switching frequency for quiet operation.
- LiPo battery low voltage warning.
- Thermal protection.
SKU: 2784 -
Shield for Arduino
PS2 Controller Starter Kit
SKU: 7438- Stable 5V powered, low current consumption, less than 150mA.
- 1 standard PS2 controller socket.
- Communicate with host microcontroller through 5V TTL UART.
- Simple inquiry command and button status feedback for the host process.
- Vibrator motor is controllable.
- Wired or wireless PS2 controller is fully compatible.
- A small LED as the indicator for communication between SKPS and PS2 controller.
SKU: 7438 -
PIC Programmer
ICSP Universal Socket
SKU: 10061ICSP Universal Socket/ICSP Adapter
To ease user, Cytron has created this UIC-A so that user can use any programmer regardless of the development board. For example, a development board which uses PICkit2’s socket standard, which is 6-way header pins can be programmed with UIC000B by using the UIC-A!
SKU: 10061 -
Brushed / Brushless DC motor Driver
Out of stock
Cytron Smartdrive40 40Amp Dc Motor Driver (Peak 80Amp) Mds40A
Brushed / Brushless DC motor DriverCytron Smartdrive40 40Amp Dc Motor Driver (Peak 80Amp) Mds40A
SKU: 2780- Bi-directional control for a single brushed DC motor.
- Support motor from 7V to 25V.
- Maximum current up to 80A peak (1 second), 40A (5 minutes) or 30A (> 20 minutes) continuously.
- 16 KHz switching frequency for quiet operation.
- Reverse polarity protection.
- LiPo battery low voltage warning.
- Thermal protection.
- Current limiting base on temperature.
SKU: 2780 -
PIC Development board
28 Pins PIC Start Up Kit – SK28A
SKU: 10080-
Industrial grade PCB.
-
Every board is being tested before it is shipped out.
-
Compact platform and breadboard-friendly
-
Suitable for hobbyists and expert.
-
Save development and soldering time.
-
Turn pin for crystal comes with 20MHz Crystal by default, the user may use crystal at various frequencies
-
Mini USB socket on board may use PIC18F2550 for USB device development, example USB Bootloader.
-
2×8 Character Parallel LCD pad ready (optional).
SKU: 10080 -
-
Shield for Arduino
Cytron Easy MP3 Shield
SKU: 7982-
Onboard high-quality MP3 decoder.
-
Onboard dual channel/Stereo 3W differential audio amplifier for an external speaker.
- A MicroSD status LED.
-
Onboard stereo 3.5mm audio jack socket for earphones.
-
Onboard microSD socket for MP3 audio files storage.
-
The interface from Arduino, UART, selectable to use soft serial.
-
Stackable side headers.
- Supply voltage: 5V.
SKU: 7982 -
-
PIC Development board
40 pins PIC Start Up Kit Combo 1 – SK40C PIC16F877A (SK40C1)
SKU: 10097-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
SKU: 10097 -
-
PIC Development board
40 pins PIC Start Up Kit Combo 2 SK40C + PIC18F4550 (SK40C2)
SKU: 10105- 40 pins PIC Start Up Kit Combo 2 SK40C + PIC18F4550 (SK40C2)
-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
-
UART connection to interface with other controller or even computer.
-
USB on board for certain PIC18F.
SKU: 10105 -
PIC Development board
40 Pins dsPIC Start Up Kit – SKDS40A
SKU: 10086-
ICSP connector for UIC00A /B-simple and fast method to load program.
-
Perfectly fit for 40 pins dsPIC (16-bit), NOT for the 40-pins 8-bit PIC.
-
2 x programmable switch.
-
2 x programmable LED indicator.
-
Changeable Crystal – default 10MHz.
-
Existing pad for 16 x 2 characters LCD display.
SKU: 10086 -
-
PIC Development board
18 Pins PIC Start Up Kit – SK18B
SKU: 10064-
Compact, powerful, flexible and robust start-up platform.
-
No extra components required for the PIC to function.
-
No more frustrated work plugging PIC out and back for re-programming.
-
Perfectly fit for 18 pins PIC16F MCU.
-
With UIC00A, the program can be loaded in less than 4 seconds.
-
On/Off switch for main power
-
DC adaptor socket as power input
SKU: 10064 -
-
USB Interface Module
USB PIC Programmer – UP00B
SKU: 10109- USB powered, no extra power needed to load program
- Two ZIF sockets (20 pins and 40 pins) to ease the program loading process
- Support most 8pin, 18pin, 28pin and 40pin PDIP 8 bit PIC MCU
- Support Windows XP, Vista, 7 (32 and 64-bits)
- Support Intel and AMD based system
- Support Laptop and desktop PC
SKU: 10109
