Arduino MEGA
Showing all 9 results
-
Shield for Arduino
L293D Motor Driver/Servo Shield for Arduino
SKU: 9736- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
- Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
SKU: 9736Boards Compatible with ArduinoMega 2560 ATmega2560-16AU Board plus USB Cable compatible with Arduino
Boards Compatible with ArduinoMega 2560 ATmega2560-16AU Board plus USB Cable compatible with Arduino
SKU: 3349- 54 Digital I/O terminals (14 of which have programmable PWM outputs).
- 16 Analog Inputs.
- 4 UARTs (hardware serial ports).
- 16 MHz crystal clock.
- Operating voltage: 6 ~ 12v.
- Dimensions: 110 x 53 x 15 mm.
SKU: 3349Boards Compatible with ArduinoMega +WiFi R3 Atmega2560+NodeMCU ESP8266 32Mb Memory USB-TTL CH340G Compatible For Arduino Mega
Boards Compatible with ArduinoMega +WiFi R3 Atmega2560+NodeMCU ESP8266 32Mb Memory USB-TTL CH340G Compatible For Arduino Mega
SKU: 110695It is a customized version of the classic ARDUINO MEGA R3 board. Full integration of Atmel ATmega2560 microcontroller and ESP8266 Wi-Fi IC, with 32 Mb (megabits) of flash memory, and CH340G USB-TTL converter on a single board! All components can be set up to work together or independently.
SKU: 110695Shield for ArduinoEthernet W5100 Shield Network Expansion Board w/ Micro SD Card Slot for Arduino
SKU: 12205- Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
- Stackable Design, can directly be supported by for Arduino official Ethernet Library.
- Supports up to four simultaneous socket connections
- Can be used to store files for serving over the network.
- Can be accessed using the Mini SD TF library.
- IEEE802.3af compliant
- Low output ripple and noise (100mVpp)
- Overload and short-circuit protection
SKU: 12205Stepper Motor Drivers3D Printer Controller Board RAMPS 1.4 Arduino Mega Shield RepRap Prusa Model
SKU: 16048- Supply Voltage: 12V
- Standard interfaces (as that of the extruder)
- Reserved GCI like I2C and RS232
- 3 MOSFET’s are applied to the heater/ fan and thermistor circuit.
- Another 5A added to protect the component parts.
- An 11A fuse is added to the hotbed.
- Support 5 stepper drive board
SKU: 16048Shield for ArduinoPrototype Shield V3.0 For Arduino Mega with breadboard
SKU: 28262- The shield can support being fully assembled with Arduino MEGA
- Support soldering components directly on this shield
- Support sticking the mini breadboards on this shield
- Reset button up top
- Mainboard aureate quadrate
- With SOP28 SMT components encapsulation
SKU: 28262Shield for ArduinoServo Driver Module Shield 16 Channel
SKU: 31371- The I2C input, PWM output control 16 roads, steering gear can 16 roads.
- The steering gear power independent V + input maximum 6 V.
- Logic signals and logical power independent output for 3V to 5 V.
- 40-1000 Hz frequency.
- Terminal block for power input.
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: 31371
Robu.in wants to send you updates. Click Allow to subscribe.
